- name: "Modbus PE1 System Status"
  unique_id: "modbus_pe1_system_status"
  state: >
    {% set mapper =  {      
      '0' : 'Continuous load',
      '1' : 'Domestic hot water',
      '2' : 'Automatic',
      '3' : 'Firewood operation',
      '4' : 'Cleaning',
      '5' : 'Boiler off',
      '6' : 'Extra heating',
      '7' : 'Chimney sweep',
      '8' : 'Cleaning' } %}
    {% set state =  states.sensor.modbus_pe1_system_status_enum.state %}
    {{ mapper[state] if state in mapper else 'Unknown' }}
  icon: >
    {% if this.state == 'Automatic' %}
      mdi:refresh-auto
    {% elif this.state == 'Domestic hot water' %}
      mdi:water-pump
    {% elif this.state == 'Continous load' %}
      mdi:hours-24
    {% else %}
      mdi:alert-circle
    {% endif %}


- name: "Modbus PE1 Furnace Status"
  unique_id: "modbus_pe1_furnace_status_mapped"
  state: >
    {% set mapper =  {
      '0' : 'FAULT',
      '1' : 'Boiler off',
      '2' : 'Heating up',
      '3' : 'Heating',
      '4' : 'Slumber',
      '5' : 'Off',
      '6' : 'Door open',
      '7' : 'Preparation',
      '8' : 'Pre-heating',
      '9' : 'Ignition',
      '10' : 'Shutdown wait',
      '11' : 'Shutdown wait 1',
      '12' : 'Shutdown feed 1',
      '13' : 'Shutdown wait 2',
      '14' : 'Shutdown feed 2',
      '15' : 'Cleaning',
      '16' : 'Wait 2h',
      '17' : 'Suction / Heating',
      '18' : 'Ignition fault',
      '19' : 'Standby',
      '20' : 'Close grate',
      '21' : 'Empty stoker',
      '22' : 'Pre-Heating',
      '23' : 'Suction',
      '24' : 'Close BBF',
      '25' : 'Open BBF',
      '26' : 'Tilt grate',
      '27' : 'Warming-Up / Ignition',
      '28' : 'Empty feed',
      '29' : 'Stoker fill',
      '30' : 'Warming-Up Lambda Probe',
      '31' : 'FD fan run-on I',
      '32' : 'FD fan run-on II',
      '33' : 'Stopped',
      '34' : 'Additional Ignition',
      '35' : 'Ignition wait',
      '36' : 'TS: Close BBF',
      '37' : 'TS: Ventilate boiler',
      '38' : 'TS: Ignition',
      '39' : 'TS: min. feed',
      '40' : 'Close BBF',
      '41' : 'FAULT: HL/ES',
      '42' : 'FAULT: Tilting grate',
      '43' : 'FAULT: C.C.Overpressure',
      '44' : 'FAULT: Door Switch',
      '45' : 'FAULT: ID Fan',
      '46' : 'FAULT: Heating system',
      '47' : 'ERROR: STL/EO',
      '48' : 'ERROR: Tilting grate',
      '49' : 'ERROR: C.C. Overpressure',
      '50' : 'ERROR: Door Switch',
      '51' : 'ERROR: ID Fan',
      '52' : 'ERROR: Heating system',
      '53' : 'ERROR: Stoker',
      '54' : 'FAULT: Stoker',
      '55' : 'TS: Empty stoker',
      '56' : 'Purge',
      '57' : 'FAULT: wood chip',
      '58' : 'ERROR: Wood chip',
      '59' : 'Emerg. Oper.: Door open',
      '60' : 'Emerg. Oper.: Heating up',
      '61' : 'Emerg. Oper.: Heating',
      '62' : 'ERROR: STL/EO',
      '63' : 'ERROR: General',
      '64' : 'Emerg. Oper.: Shutdown',
      '65' : 'Self test active',
      '66' : 'Troubleshooting 20min',
      '67' : 'ERROR: Drop box',
      '68' : 'FAULT: Drop box',
      '69' : 'Cleaning possible',
      '70' : 'Heating - Cleaning',
      '71' : 'LW Heating up',
      '72' : 'LW Heating',
      '73' : 'LW Heat/Shut down',
      '74' : 'FAULT save',
      '75' : 'FGR run-on',
      '76' : 'Clean FGR',
      '77' : 'Igniton OFF',
      '78' : 'Cleaning filter',
      '79' : 'Heating wizard',
      '80' : 'Ignite firewood boiler',
      '81' : 'SH fault',
      '82' : 'Sensor check' } %}
    {% set state =  states.sensor.modbus_pe1_furnace_status_enum.state %}
    {{ mapper[state] if state in mapper else 'Unknown' }}
  icon: >
    {% if this.state == 'Standby' %}
      mdi:sleep
    {% elif this.state == 'Ignition' %}
      mdi:fire
    {% elif this.state == 'Pre-heating' %}
      mdi:fire
    {% elif this.state == 'Heating' %}
      mdi:fire
    {% elif this.state == 'Heating up' %}
      mdi:fire
    {% elif this.state == 'Preparation' %}
      mdi:fire
    {% elif this.state == 'Shutdown wait' %}
      mdi:sleep
    {% elif this.state == 'Shutdown wait 1' %}
      mdi:sleep
    {% elif this.state == 'Shutdown wait 2' %}
      mdi:sleep
    {% else %}
      mdi:alert-circle
    {% endif %}

- name: "Modbus PE1 Heating Mode"
  unique_id: "modbus_pe1_heating_mode"
  state: >
    {% set mapper =  {
      '0' : 'Off',
      '1' : 'Automatic',
      '2' : 'Extra heating',
      '3' : 'Setback',
      '4' : 'Continuous setback',
      '5' : 'Party mode' } %}
    {% set state =  states.sensor.modbus_pe1_heating_mode_enum.state %}
    {{ mapper[state] if state in mapper else 'Unknown' }}
  icon: >
    {% if this.state == 'Off' %}
      mdi:power
    {% elif this.state == 'Automatic' %}
      mdi:clock
    {% elif this.state == 'Extra heating' %}
      mdi:sun-clock
    {% elif this.state == 'Setback' %}
      mdi:moon-waning-crescent
    {% elif this.state == 'Continuous setback' %}
      mdi:thermometer-minus
    {% elif this.state == 'Party mode' %}
      mdi:white-balance-sunny
    {% else %}
      mdi:alert-circle
    {% endif %}

  - name: Visualization Is Heating Active
    unique_id: "visualization_heating_active"
    state: >
        {% if states('sensor.modbus_pe1_flow_temperature_target') | int > 0%}
          true
        {% else %}
          false
        {% endif %}

  - name: Visualization Is Buffer Cold
    unique_id: "visualization_buffer_cold"
    state: >
        {% if states('sensor.modbus_pe1_buffer_temperature_bottom') | int < 30 and states('sensor.modbus_pe1_buffer_temperature_top') | int < 30%}
          true
        {% else %}
          false
        {% endif %}
  - name: Visualization Is Buffer Cold Warm
    unique_id: "visualization_buffer_cold_warm"
    state: >
        {% if states('sensor.modbus_pe1_buffer_temperature_bottom') | int < 30 and states('sensor.modbus_pe1_buffer_temperature_top') | int >= 30 and states('sensor.modbus_pe1_buffer_temperature_top') | int < 50%}
          true
        {% else %}
          false
        {% endif %}
  - name: Visualization Is Buffer Cold Hot
    unique_id: "visualization_buffer_cold_hot"
    state: >
        {% if states('sensor.modbus_pe1_buffer_temperature_bottom') | int < 30 and states('sensor.modbus_pe1_buffer_temperature_top') | int >= 50%}
          true
        {% else %}
          false
        {% endif %}
  - name: Visualization Is Buffer Warm Cold
    unique_id: "visualization_buffer_warm_cold"
    state: >
        {% if states('sensor.modbus_pe1_buffer_temperature_bottom') | int >= 30 and states('sensor.modbus_pe1_buffer_temperature_bottom') | int < 50 and states('sensor.modbus_pe1_buffer_temperature_top') | int < 30%}
          true
        {% else %}
          false
        {% endif %}
  - name: Visualization Is Buffer Warm
    unique_id: "visualization_buffer_warm"
    state: >
        {% if states('sensor.modbus_pe1_buffer_temperature_bottom') | int >= 30 and states('sensor.modbus_pe1_buffer_temperature_bottom') | int < 50 and states('sensor.modbus_pe1_buffer_temperature_top') | int >= 30 and states('sensor.modbus_pe1_buffer_temperature_top') | int < 50%}
          true
        {% else %}
          false
        {% endif %}
  - name: Visualization Is Buffer Warm Hot
    unique_id: "visualization_buffer_warm_hot"
    state: >
        {% if states('sensor.modbus_pe1_buffer_temperature_bottom') | int >= 30 and states('sensor.modbus_pe1_buffer_temperature_bottom') | int < 50 and states('sensor.modbus_pe1_buffer_temperature_top') | int >= 50%}
          true
        {% else %}
          false
        {% endif %}
  - name: Visualization Is Buffer Hot Warm
    unique_id: "visualization_buffer_hot_warm"
    state: >
        {% if states('sensor.modbus_pe1_buffer_temperature_top') | int >= 30 and states('sensor.modbus_pe1_buffer_temperature_top') | int < 50 and states('sensor.modbus_pe1_buffer_temperature_bottom') | int >= 50%}
          true
        {% else %}
          false
        {% endif %}
  - name: Visualization Is Buffer Hot
    unique_id: "visualization_buffer_hot"
    state: >
        {% if states('sensor.modbus_pe1_buffer_temperature_bottom') | int >= 50 and states('sensor.modbus_pe1_buffer_temperature_top') | int >= 50 %}
          true
        {% else %}
          false
        {% endif %}
  - name: Visualization Is Radiator Cold
    unique_id: "visualization_radiator_cold"
    state: >
        {% if states('sensor.modbus_pe1_flow_temperature_actual') | int < 30%}
          true
        {% else %}
          false
        {% endif %}
  - name: Visualization Is Radiator Warm
    unique_id: "visualization_radiator_warm"
    state: >
        {% if states('sensor.modbus_pe1_flow_temperature_actual') | int >= 30 and states('sensor.modbus_pe1_flow_temperature_actual') | int < 40%}
          true
        {% else %}
          false
        {% endif %}
  - name: Visualization Is Radiator Hot
    unique_id: "visualization_radiator_hot"
    state: >
        {% if states('sensor.modbus_pe1_flow_temperature_actual') | int >= 40%}
          true
        {% else %}
          false
        {% endif %}
  - name: Buffer Pump Status
    unique_id: "visualization_buffer_pump_status"
    state: >
      {% if states('sensor.modbus_pe1_buffer_pump_control') | float(0) > 0%}
        on
      {% else %}
        off
      {% endif %}
    icon: >
      {% if this.state == 'on' %}
        mdi:pump
      {% else %}
        mdi:pump-off
      {% endif %}
  - name: Boiler Pump Status
    unique_id: "visualization_water_boiler_pump_status"
    state: >
      {% if states('sensor.modbus_pe1_water_boiler_pump_control') | float(0) > 0%}
        on
      {% else %}
        off
      {% endif %}
    icon: >
      {% if this.state == 'on' %}
        mdi:pump
      {% else %}
        mdi:pump-off
      {% endif %}